[KR155E]

A problem often encountered by Virtual Boy users are glitchy displays, leading to horizontal lines, reversed or generally distorted images, or even complete loss of display activity.

All those symptoms are usually caused by the ribbon cables connecting the LEDs to the motherboard becoming loose, or peeling away from the display PCB.

Fixing your Diplay: Oven method

DogP has come up with a way to fix the problem by opening the system up, removing the display, sticking it in the oven to re-melt the adhesive, and reassemble. It’s not a difficult procedure, except that the typical security bit can’t get to the deepest screws on the VB, so you either need a special screwdiver, a modified bit, or a modified screwdriver.

You can find a guide to fix your displays on DogP’s Project:VB.

Fixing your Diplay: Bypass method

Another way has been proposed by DanB. To permanently fix the problem, his idea was to replace the loosening ribbon cables with some better wires, which he soldered to the PCB. This solution requires much more skill, though, and should only be performed by solder experienced people with a steady hand and a huge portion of patience.

The complete guide can be found here.

Fixing your Diplay: New methods (RECOMMENDED)

Some more methods have recently been developed by DogP to permanently fix the cable problem (contrary to the probably non-permanent oven method): Thread.

• This topic was modified 16 years, 4 months ago by KR155E.

Lester Knight wrote:
i bought my gamebit off ebay and then modified it to fit my virtual boy. HERE are instructions.

you can also modify a screw driver by fileing out a notch at the bottom so that it can grip the security screws on 2 sides.

you should consider replacing the screws after you get them out. any hardware store should sell a #4 X 1/2 PAN PHIL screw. to make the job easier consider someting to magnetize your driver

good luck and welcome to the world of the virtual boy!

Thanks!
Well, I’ve been trying with a few more games and sometimes both screens are on and then start messing with the lines and all, so I guess the problem is the same as reported by other people.
Anyway, thanks for the tip, but I don’t have neither the means nor the knowledge to do that hehe. That sucks, because from what I’ve read here, there’s no “off the shelf” screwdriver that can get to the deep screws of the VB, right? Found this: http://www.newelectronx.com/join-email-list.php?letter_id=68&lettertype=&pageaction=browse but in this very forum it’s said that those don’t work either… Bic pens are too thick… what am I to do?

Thanks again

EDIT: Well, this: loks more feasible to me…

Chavaflyfree wrote:

Lester Knight wrote:
i bought my gamebit off ebay and then modified it to fit my virtual boy. HERE are instructions.

you can also modify a screw driver by fileing out a notch at the bottom so that it can grip the security screws on 2 sides.

you should consider replacing the screws after you get them out. any hardware store should sell a #4 X 1/2 PAN PHIL screw. to make the job easier consider someting to magnetize your driver

good luck and welcome to the world of the virtual boy!

Thanks!
Well, I’ve been trying with a few more games and sometimes both screens are on and then start messing with the lines and all, so I guess the problem is the same as reported by other people.
Anyway, thanks for the tip, but I don’t have neither the means nor the knowledge to do that hehe. That sucks, because from what I’ve read here, there’s no “off the shelf” screwdriver that can get to the deep screws of the VB, right? Found this: http://www.newelectronx.com/join-email-list.php?letter_id=68&lettertype=&pageaction=browse but in this very forum it’s said that those don’t work either… Bic pens are too thick… what am I to do?

Thanks again

I bought this on: http://www.ebay.de/itm/4-5mm-Security-Screw-Bit-Lifetime-Warranty-Uscrew-Virtual-Boy-System-/171049124774?pt=US_Video_Gaming_Replacement_Parts_Tools&hash=item27d35283a6 from the same seller.

It worked perfectly fine. Shipping was extremely fast considering the fact it was send from the states to Germany.

thunderstruck wrote:

I bought this on: http://www.ebay.de/itm/4-5mm-Security-Screw-Bit-Lifetime-Warranty-Uscrew-Virtual-Boy-System-/171049124774?pt=US_Video_Gaming_Replacement_Parts_Tools&hash=item27d35283a6 from the same seller.

It worked perfectly fine. Shipping was extremely fast considering the fact it was send from the states to Germany.

Thanks! That’s more like it.
Thanks to that I’ve managed to find also this one, shipping from UK which hsould work, right? http://www.ebay.es/itm/4-5MM-SECURITY-SCREWDRIVER-NINTENDO-GAMECUBE-SNES-N64-MEGADRIVE-/380653675974?pt=UK_VG_Replacement_Parts_Tools&hash=item58a0ba25c6#shpCntId

And this one from Spain… http://retrocables.es/tienda/index.php?id_product=222&controller=product&id_lang=4

Thanks for your help!

Chavaflyfree wrote:

thunderstruck wrote:

I bought this on: http://www.ebay.de/itm/4-5mm-Security-Screw-Bit-Lifetime-Warranty-Uscrew-Virtual-Boy-System-/171049124774?pt=US_Video_Gaming_Replacement_Parts_Tools&hash=item27d35283a6 from the same seller.

It worked perfectly fine. Shipping was extremely fast considering the fact it was send from the states to Germany.

Thanks! That’s more like it.
Thanks to that I’ve managed to find also this one, shipping from UK which hsould work, right? http://www.ebay.es/itm/4-5MM-SECURITY-SCREWDRIVER-NINTENDO-GAMECUBE-SNES-N64-MEGADRIVE-/380653675974?pt=UK_VG_Replacement_Parts_Tools&hash=item58a0ba25c6#shpCntId

And this one from Spain… http://retrocables.es/tienda/index.php?id_product=222&controller=product&id_lang=4

Thanks for your help!

No idea. The one I bought was delivered within a one and a half weeks and it worked perfectly. If you are not sure what to buy I would go for that one.

thunderstruck wrote:
No idea. The one I bought was delivered within a one and a half weeks and it worked perfectly. If you are not sure what to buy I would go for that one.

Thanks, you’re right I’d buy that one since it’s the only one that seem to work 🙂

Argh,
Managed to get a gamebit screwdriver that fits perfectly. I’m able to unscrew all of them except one.
It seems this one has been stripped… and by the looks of it, pretty badly (and to make things worse, is one of the deepest screws). Maybe this is one of the reasons this VB was so cheap…

See attached pic!

It kind of looks corroded or something. I’ve spent the whole morning and been unable to unscrew that. The gamebit just doesn’t “stick” (works great with the rest though).

Any ideas? Is such a unreachable place that I don’t know what to do.
Could that be cleaned with anything? I don’t even think it can be cut off…

Any idea is more than welcome.

Thanks in advance

Attachments:

1. 

   screw-scaled.jpg
   

i can’t tell from that photo what is wrong with it. are the sides noticeably stripped, so you are assuming someone must have tried to unscrew it before? if the sides are not stripped and the screw is just stuck, try tightening it a little bit and then untightening, as this may pry it loose.

Chavaflyfree wrote

Any ideas? Is such a unreachable place that I don’t know what to do.
Could that be cleaned with anything? I don’t even think it can be cut off… Any Idea is more than welcome

I’m not telling you to do this. Nor will I be responsible if it doesn’t work for you I’m just saying that these Ideas worked for these guys and they could scratch that may work for you

http://www.virtual-boy.org/hmdvb.htm

http://www.digitpress.com/forum/showthread.php?136424-Opening-a-Virtual-Boy

good luck.

Chavaflyfree wrote:

Managed to get a gamebit screwdriver that fits perfectly.

Not familiar with that screwdriver — is it a tube with splines on the inside? If you caught my earlier comment, I took an old philip’s screw-driver and filed it flat on the end (think I heated it and removed the temper first); then drilled it out so it fit snug on the screws, then tapped the end three times with a chisel (making six little tabs that grab the screws perfectly); then heated it in a blow-torch to cherry red and quenched it (re-tempered). Works fine, bet there’s enough of your screw head left to work (unless your gamebit is already that shape).

The next move if all else fails, is to drill a hole into the head with a small drill-bit (hardest part will be getting the bit STARTED, centered would be nice), then use an “easy-out”. The screw is after all, metal — and it’s stuck in plastic. The plastic’s alot weaker than the screw…

vb-fan wrote:
Not familiar with that screwdriver — is it a tube with splines on the inside? If you caught my earlier comment, I took an old philip’s screw-driver and filed it flat on the end (think I heated it and removed the temper first); then drilled it out so it fit snug on the screws, then tapped the end three times with a chisel (making six little tabs that grab the screws perfectly); then heated it in a blow-torch to cherry red and quenched it (re-tempered). Works fine, bet there’s enough of your screw head left to work (unless your gamebit is already that shape).

The next move if all else fails, is to drill a hole into the head with a small drill-bit (hardest part will be getting the bit STARTED, centered would be nice), then use an “easy-out”. The screw is after all, metal — and it’s stuck in plastic. The plastic’s alot weaker than the screw…

Thanks for your comments. You’re right, I’ll try to get the philips flat and drill it out. I can barely see inside the deep hole, but I hope the screw head still keeps a couple of marks to grab onto.

Thanks again!

I just came across something interesting… Z-axis Conductive Tape (like: https://www.sparkfun.com/products/12042 ). I think this (or something similar) might have been what they originally used at the factory for these cables. According to 3M, it’s main purpose is for connecting flex circuits to other to other flex circuits or PCBs.

Here’s an interesting quote from the datasheet:

Mechanical Clamping
To assure electrical resistance stability of Tape 9703 in any flexible circuit interconnection application, a mechanical clamp or other compressive force (i.e. foam strip held in compression over bond area.) should be considered in the design of the application. Any stress inherent in the assembly design (i.e. tensile, shear, cleavage) or temperature excursions (encountered through normal product use) applied to the bond area could result in an electrical open in the bonded circuit over time when no clamp or mechanism for maintaining a constant compressive forces is used. A well designed mechanical clamp will reduce the environmental stress on the bond line and improve the electrical reliability of the bond. In addition, the temperature operating range for the adhesive can be improved with a properly designed mechanical clamping system to ensure the conducting particles in the Tape 9703 maintain electrical contact. Several types of
mechanical clamps have been used successfully including foam strips attached to lids or cases and screw-attached plastic clamps. Contact your 3M Technical Service Engineer for further information about mechanical clamping.

So, if that’s what was used, and with no mechanical clamping… I guess even the manufacturer could have guessed that it’d fail.

Anyway, if anyone is looking for a solder-free method to fix displays… carefully peeling the cable from the display, cleaning the contacts, and carefully aligning/sticking the cable back down might be a possible solution. Of course a mechanical clamp would be a good idea, like: http://www.planetvb.com/modules/newbb/viewtopic.php?post_id=25208#forumpost25208 . And actually, if anyone is looking to try this, I’d be glad to perfect that clamp design and mail you a set (you need to provide your own Z-axis tape though… I don’t have any yet).

The datasheet specifies the minimum gap as 15 mil (0.4 mm), though below, it says “Minimum free space between adjacent conductors suggested to ensure electrical isolation. Customers may qualify finer pitch performance in their applications.”… so it sounds like it should work smaller, but you need to verify that there are no shorts. I believe the gap is approximately 0.3mm on our cable.

On another note… I want to see someone use it as an alternative to soldering BGAs, like they did for the QFP in the Sparkfun video. 😉 “Aww man… BGA rework is such a hassle” . 😉

DogP

I’ll give it a try, thanks DogP :] What could go wrong if it makes shortcuts everywhere after all ?

OK so I fired up my little red buddy and my right screen was way outa wack. so I talked it over w my very smart friend and he said it’s probably the mirror sensor and I should buy some compressed air to fix it up. So I tried that screwed it all together and everything was Hunky Dorey until…I changed the IPD and then all heck broke loose. I instantly knew it wasn’t the PCB connection my I got that fixed and the guy that did it did a bangin job I might add. So I had to diagnose it all by my lonesome. So I prayed about it and then I opened it again and noticed that my left PCB flexable circuit was creased, not beyond repair just enough so It was screwing with the display. so I carefully removed the PCB and got out a towel to Iron on and a good iron made sure that there was’nt any water in the iron. Got the old iron hot on the lowest setting not hot enough to melt the PCB flexable circuit just barely hot enough to be uncomfortable on your hand then I unpluged the iron and Ironed out the PCB flexable circuit. Put in Vertical Force and sure enough it was good as new.

DISCLAIMER

Now I’m not telling you to do this I’m just saying it worked for me. if you decide to do this on your own Be extremely careful w the heat setting of the iron if it’s too hot it’s GAME OVER NO SECOND CHANCES IT’S TOAST. Check the iron over and over again by touching it and making sure it’s not too hot. I even unplugged the iron.

Let me first tell you this, I am not saying the person who repaired your screen didn’t do a bang up job, it can sometimes happen that a connection isn’t completely through and through, it has happened twice to me.
With that out of the way, I think there is a problem with the soldering Morintary and the Iron trick just helped getting the trace on the display board for a while, just like the oven trick.

The problem you are describing with the IPD is something I have seen myself a few times when soldering displays. It means that one or more traces didn’t get a good connection while soldering.
I just got one display back from a member here that had the same problem which I barely got right again, though I did. You can’t see it with the naked eye, but it surely must have been a bad connection in your case as well. So be warned that it probably will come back.

If a crease in the cable would really have been the problem, it wouldn’t have been repairable like you did as copper doesn’t work that way.

I finally managed to “level up” my soldering skill and fix one of my displays :). After applying NaOH per DogP’s instructions, and putting it in the oven for a short time (along with some rosemary sprigs and a dash of salt), I was able to peel away the remaining plastic on the cable to get at the copper contacts.

It took me a while to get this whole project done, partially because of my lack of soldering experience, but also because I messed up when cleaning the bared contacts with a fiberglass pencil. Some copper from the flex cable was getting peeled up instead of just being polished clean on the first PCB I did. I also think perhaps not all of the plastic from the cable had dissolved. So on the second one, I very carefully used a pushpin thumbtack to peel up the remaining plastic. I held the pushpin over the PCB, with the needle end facing up towards the flex cable. Then, just gently worked the tip under the remaining plastic of the cable (between the copper contacts of course).

After a few times powering on the VB to test my work, the displays were somewhat working until I finally found an area with an obvious short circuit/sloppy solder job. Now, that display works almost like new!

One final question (sigh…)- how should I clean the oscillating mirror?? I know the right answer is “I shouldn’t clean it”. There seems to be a smudge or something on it, which at first seemed like tiny scratches on the red plastic lens my peripheral vision would pick up. But, I can see now it’s actually on the mirror >:|. Not sure how it got there either, I was always careful not to touch it and always wore an N95 respirator mask when the VB unit was opened up so I didn’t blow any dust in.

In case anyone was wondering, I bought a Kendal 937D soldering station on Amazon for like $50. Comes with 5 tips (two are tiny ones, perfect for this project), and has a very accurate temperature knob/display. Heats up VERY fast as well.

Enough rambling- thanks to DogP for the great post on how to carry out this project! Also thanks to TheForce81 and RunnerPack for their advice in the matter as well 🙂

Attachments:

1. 

   pcb1b.jpg
   

2. 

   pcb1mount.jpg
   

Craby wrote:
I’ll give it a try, thanks DogP :] What could go wrong if it makes shortcuts everywhere after all ?

Heh, hopefully nothing… I’ve had several shorts over the years, and never seen any permanent problems (always cleared up as soon as I removed the short). Not to say that a bunch of them won’t hurt it, but a simple test with a multimeter should let you verify before powering it up.

HP Lovethrash wrote:
One final question (sigh…)- how should I clean the oscillating mirror?? I know the right answer is “I shouldn’t clean it”. There seems to be a smudge or something on it, which at first seemed like tiny scratches on the red plastic lens my peripheral vision would pick up. But, I can see now it’s actually on the mirror >:|. Not sure how it got there either, I was always careful not to touch it and always wore an N95 respirator mask when the VB unit was opened up so I didn’t blow any dust in.

Nice work… about the smudge, are you SURE it’s on the mirror? I’ve noticed dark lines several times, where it seems like it’d be the mirror or the red lens… but it’s actually dirt/dust on the clear cover over the LED bar. A simple wiping of the clear cover takes care of it.

DogP

DogP wrote

I’ve noticed dark lines several times, where it seems like it’d be the mirror or the red lens… but it’s actually dirt/dust on the clear cover over the LED bar. A simple wiping of the clear cover takes care of it.

DogP are you referring to the lens in front of the LED? or something else?

Yeah, the clear lens on the front of the display board.

DogP

I had the foresight to give the clear covers a good wipe with a microfiber cloth before screwing them back in. I can see some kind of smudge or faint smear on the left mirror though. However, I got to wondering if that’s not part of the issue- would a fleck of dust on the mirror create little black lines on the display? Once the mirror oscillates, the dust would appear more as a small line than a speck, or so my brain would think. Maybe I will try using an air can to blow out any stray particles.

The little lines I see are only noticeable over brighter red areas, the title screen for 3D Tetris is a good example. They aren’t huge, straight lines like the original display problem…just little annoying ones that seem to move or shrink somewhat if I move my head to the side slightly while playing.

Still kind of curious why the mirror looks streaky at a certain angle, maybe it’s a non-issue…

DogP wrote:
Yeah, the clear lens on the front of the display board.

DogP

Can someone clarify something for me about these glitches? Everyone seems to be complaining of a horizontal glitch which I’ve seen before and it bothers me but less so. I’ve recently been seeing a vertical set of lines sort of like a bar graph but much slimmer that seem to come and go frequently and seem to be more black than red. Are those just the same or do I have a different problem entirely?